They are the Thermocouples which cover the widest range of use, from chemical processes to incinerators. The TC Series has been developed to ensure the best performace-service-cost ratio, from the ease of selection and ordering to the product's maximum reliability and endurance. Based essentially on DIN norms and thanks to the variety of options, the TC Series also fulfils the other international standards （ISO, ANSI, ...）, which are commonly followed in the practice of engineering. Type J or type K, grounded or ungrounded measurement junction, general purpose or Atex certified transmitter, can simply be selected according to your requirements. Furthermore, in the case of applications in industrial furnaces or in the field of primaries, the TAF Thermocouples are often the best-fitting solution. Thermocouple sensor with compression fitting. The thermometer TEC420 comprises a TEC100 6 mm diameter inset with either a transmitter mounting plate or a ceramic terminal block. The hot junction can be either grounded or isolated from the sheath. The terminal head can be selected from a wide choice of standard items.  E+H工業熱電偶Omnigrad T TEC420
TEC420 sheathed thermocouples cover temperature ranges from -40°C to 1100°C depending on the type of thermocouple. They can be used in low pressure applications in direct contact with the medium or protected by a thermowell. They can also be used in all applications where small immersion lengths are needed. Special attention should be paid to the maximum operating temperature of the connection head （80°C if transmitter included）. Omnigrad M TC10 
- To screw in
- Thermowell acc. DIN 43772/2G+3G
- Replacable insert, MgO
- Type J （Fe-CuNi）
Range: -40...750°C
（-40...1382°F） - Type K （NiCR-Ni）
Range: -40...1100°C
（-40...2012°F）
TC12 
- With compression fitting
- Thermowell acc. DIN 43772/2+3
- Replacable insert, MgO
- Type J （Fe-CuNi）
Range: -40...750°C
（-40...1382°F） - Type K （NiCR-Ni）
Range: -40...1100°C
（-40...2012°F）
TC13 
- With flange
- Thermowell acc. DIN 43772/2F+3F
- Replacable insert, MgO
- Type J （Fe-CuNi）
Range: -40...750°C
（-40...1382°F） - Type K （NiCR-Ni）
Range: -40...1100°C
（-40...2012°F）
Omnigrad S TC15
- Thermowell acc. DIN 43772/4 + 4F
- Interchangeable insert, MgO
- Type J （Fe-CuNi）
Range: -40...750°C
（-40...1382°F） - Type K （NiCr-Ni）
Range: -40...1100°C
（-40...2012°F）
TC88 
- To screw-in in an existing thermowell
- Degree of protection up to IP 68
- Replaceable insert, MgO
- Type J （Fe-CuNi）
Range: -40...750 °C
（-40...1382 °F） - Type K （NiCr-Ni）
Range: -40...1100 °C
（-40...2012 °F）
德國E+H工業熱電偶由一對或多對熱電極與絕緣物組成的組件，用來防止熱電極之間和（或）熱電極與保護管之間短路的零件或材料，保護熱電極組件免受環境有害影響的管狀物，若與所配用的熱電偶正確連接，就把熱電偶的參比端移至這對導線的輸出端。 在溫度出現階躍變化時，E+H工業熱電偶的輸出變化至相當于該階躍變化的某個規定百分數所需的時間，通常以τ表示。 |
